Screws

Thread Diameter - Pitch: M5-0.80
Length: 6mm
Slotted pan heads have a flat or gently rounded top surface, cylindrical sides and a flat bearing surface. This general purpose head has a flat bearing surface with a short disc-like body and a slightly rounded top surface. Can be used in most situations when general bearing strength is needed. Can be substitutedin most applications for round, truss or binding heads.

Thread Diameter - Pitch: M5-0.80
Length: 12mm
Slotted pan heads have a flat or gently rounded top surface, cylindrical sides and a flat bearing surface. This general purpose head has a flat bearing surface with a short disc-like body and a slightly rounded top surface. Can be used in most situations when general bearing strength is needed. Can be substitutedin most applications for round, truss or binding heads.

Thread Diameter - Pitch: M5-0.80
Length: 6mm
Phillips pan heads have a rounded top, cylindrical sides and a flat bearing surface. This general purpose head has a flat bearing surface with a short disc-like body and a slightly rounded top surface. Can be used in most situations when general bearing strength is needed.

Thread Diameter - Pitch: M5-0.80
Length: 8mm
Phillips pan heads have a rounded top, cylindrical sides and a flat bearing surface. This general purpose head has a flat bearing surface with a short disc-like body and a slightly rounded top surface. Can be used in most situations when general bearing strength is needed.

Thread Diameter - Pitch: M5-0.80
Length: 10mm
Phillips pan heads have a rounded top, cylindrical sides and a flat bearing surface. This general purpose head has a flat bearing surface with a short disc-like body and a slightly rounded top surface. Can be used in most situations when general bearing strength is needed.

Thread Diameter - Pitch: M5-0.80
Length: 12mm
Phillips pan heads have a rounded top, cylindrical sides and a flat bearing surface. This general purpose head has a flat bearing surface with a short disc-like body and a slightly rounded top surface. Can be used in most situations when general bearing strength is needed.

Thread Diameter - Pitch: M5-0.80
Length: 16mm
Phillips pan heads have a rounded top, cylindrical sides and a flat bearing surface. This general purpose head has a flat bearing surface with a short disc-like body and a slightly rounded top surface. Can be used in most situations when general bearing strength is needed.

Thread Diameter - Pitch: M5-0.80
Length: 20mm
Phillips pan heads have a rounded top, cylindrical sides and a flat bearing surface. This general purpose head has a flat bearing surface with a short disc-like body and a slightly rounded top surface. Can be used in most situations when general bearing strength is needed.

Thread Diameter - Pitch: M5-0.80
Length: 30mm
Phillips pan heads have a rounded top, cylindrical sides and a flat bearing surface. This general purpose head has a flat bearing surface with a short disc-like body and a slightly rounded top surface. Can be used in most situations when general bearing strength is needed.

Thread Diameter - Pitch: M5-0.80
Length: 35mm
Phillips pan heads have a rounded top, cylindrical sides and a flat bearing surface. This general purpose head has a flat bearing surface with a short disc-like body and a slightly rounded top surface. Can be used in most situations when general bearing strength is needed.

Thread Diameter - Pitch: M5-0.80
Length: 40mm
Phillips pan heads have a rounded top, cylindrical sides and a flat bearing surface. This general purpose head has a flat bearing surface with a short disc-like body and a slightly rounded top surface. Can be used in most situations when general bearing strength is needed.

Thread Diameter - Pitch: M5-0.80
Length: 45mm
Phillips pan heads have a rounded top, cylindrical sides and a flat bearing surface. This general purpose head has a flat bearing surface with a short disc-like body and a slightly rounded top surface. Can be used in most situations when general bearing strength is needed.

Thread Diameter - Pitch: M5-0.80
Length: 50mm
Phillips pan heads have a rounded top, cylindrical sides and a flat bearing surface. This general purpose head has a flat bearing surface with a short disc-like body and a slightly rounded top surface. Can be used in most situations when general bearing strength is needed.

Thread Diameter - Pitch: M5-0.80
Length: 8mm
The Flat Head Screw features a countersunk head with a flat top surface and a cone-shaped bearing surface with a head angle of approximately 82 degrees. Used in applications where protrusion of the fastener above the mating surface is unacceptable. Use a protrusion gage when measuring head height. Phillips drive is x-shaped for installation with a phillips screw driver.

Thread Diameter - Pitch: M5-0.80
Length: 10mm
The Flat Head Screw features a countersunk head with a flat top surface and a cone-shaped bearing surface with a head angle of approximately 82 degrees. Used in applications where protrusion of the fastener above the mating surface is unacceptable. Use a protrusion gage when measuring head height. Phillips drive is x-shaped for installation with a phillips screw driver.

Thread Diameter - Pitch: M5-0.80
Length: 12mm
The Flat Head Screw features a countersunk head with a flat top surface and a cone-shaped bearing surface with a head angle of approximately 82 degrees. Used in applications where protrusion of the fastener above the mating surface is unacceptable. Use a protrusion gage when measuring head height. Phillips drive is x-shaped for installation with a phillips screw driver.

Thread Diameter - Pitch: M5-0.80
Length: 16mm
The Flat Head Screw features a countersunk head with a flat top surface and a cone-shaped bearing surface with a head angle of approximately 82 degrees. Used in applications where protrusion of the fastener above the mating surface is unacceptable. Use a protrusion gage when measuring head height. Phillips drive is x-shaped for installation with a phillips screw driver.

Thread Diameter - Pitch: M5-0.80
Length: 20mm
The Flat Head Screw features a countersunk head with a flat top surface and a cone-shaped bearing surface with a head angle of approximately 82 degrees. Used in applications where protrusion of the fastener above the mating surface is unacceptable. Use a protrusion gage when measuring head height. Phillips drive is x-shaped for installation with a phillips screw driver.

Thread Diameter - Pitch: M5-0.80
Length: 25mm
The Flat Head Screw features a countersunk head with a flat top surface and a cone-shaped bearing surface with a head angle of approximately 82 degrees. Used in applications where protrusion of the fastener above the mating surface is unacceptable. Use a protrusion gage when measuring head height. Phillips drive is x-shaped for installation with a phillips screw driver.

Thread Diameter - Pitch: M5-0.80
Length: 30mm
The Flat Head Screw features a countersunk head with a flat top surface and a cone-shaped bearing surface with a head angle of approximately 82 degrees. Used in applications where protrusion of the fastener above the mating surface is unacceptable. Use a protrusion gage when measuring head height. Phillips drive is x-shaped for installation with a phillips screw driver.