Machine Screws

Thread Diameter - Pitch: #12-24
Length: 1 1/2"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: #10-32
Length: 1"
The head and washer are combined into a single unit, which spread out clamping force of the fastener on the joint. This fastener head is very similar to a hex flange head. Offers greater protection to the mating surface than a standard indented hex head. Increased bearing area reduces likelihood of crushing mating surfaces.

Thread Diameter - Pitch: #10-24
Length: 1/2"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: #10-24
Length: 5/8"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: #10-24
Length: 3/4"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: #10-24
Length: 1"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: #10-24
Length: 1 1/2"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: #10-32
Length: 1 1/2"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: #10-24
Length: 2"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: 1/4-20
Length: 1/2"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: 1/4-20
Length: 5/8"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: 1/4-20
Length: 3/4"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: 1/4-20
Length: 1"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: 1/4-20
Length: 1 1/4"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: 1/4-20
Length: 1 1/2"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: 1/4-20
Length: 2"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: #8-32
Length: 3/8"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: #10-24
Length: 1/4"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: #10-24
Length: 3/8"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.

Thread Diameter - Pitch: #10-32
Length: 1"
Has six flat sides, and a flat bearing surface. Preferred in high volume assembly where pneumatic equipment is used to drive the screw.